Bulletin, Volume 20,Bagian 1American Society for Testing and Materials., 1920 Vols. 1-61 include reports of the 1st-64th annual meetings, committee reports and technical papers; v.16-38 include also "New and revised tentative standards [and] tentative revisions of standards" (varies slightly) |
Edisi yang lain - Lihat semua
Istilah dan frasa umum
22 GAGE A.S.T.M. Standards adoption as standard aggregate alloys American Society annual meeting Antimony average babbitt metal bars brick bromine Carbon Cement cent Chairman clay Coarse Committee A-1 Compressive Strength Copper Copper-bearing cubic cubic foot curves determined diameter Engineering Executive Committee grade gypsum hexabromide ingot inspection Iron Joint Committee laboratory letter ballot linseed oil machine Manganese manufacturer measure metal Method of Filling mittee mixed mixture OPEN-HEARTH percentage permissible variations Phosphorus pipe plates Portland Cement present Proposed Tentative quantity recommended rejected report of Committee represent requirements sample sand Secretary-Treasurer Serial Designation sheets sieve sieve analysis slag Society for Testing solution Soya Bean specified in Section Standard Specifications standing committees Steel strength of concrete Sub-Committee sulfur Table tannic acid tensile tensile strength tension test Tentative Methods Tentative Specifications tentative standards Tentative Test test specimen thickness tube Tung Oil voting
Bagian yang populer
Halaman 521 - If the purchaser elects to have inspection made at the manufacturer's works, the inspector representing the purchaser shall have free entry, at all times while work on the contract of the purchaser is being performed, to all parts of manufacturer's works which concern the manufacture of the material ordered.
Halaman 454 - Section 5, which represent rejected tie plates, shall be preserved for two weeks from the date of the test report. In case of dissatisfaction with the results of the tests, the manufacturer may make claim for a rehearing within that time.
Halaman 509 - The gage length, parallel section, and fillets shall be as shown, but the ends may be of any shape to fit the holders of the testing machine in such a way that the load shall be axial.
Halaman 456 - The specimen shall be either nicked with a chisel or grooved on a machine, transversely, about ^5 in. deep, in three places about 2 in. apart. The first groove shall be made 2 in. from the square end ; each succeeding groove shall be made on the opposite side from the preceding one. The specimen shall then be firmly held in a vise, with the first groove about J in.
Halaman 721 - F.) to that of an equal volume of water at the same temperature and shall be expressed thus: Specific Gravity 25°/25° C.
Halaman 454 - ... works which concern the manufacture of the tie plates ordered. The manufacturer shall afford the inspector, free of cost, all reasonable facilities to satisfy him that the tie plates are being furnished in accordance with these specifications. All tests (except check analyses) and inspection shall be made at the place of manufacture prior to shipment, unless otherwise specified, and shall be so conducted as not to interfere unnecessarily with the operation of the works.
Halaman 456 - For material 1 in. or under in thickness, around a pin the diameter of which is equal to the thickness of the specimen; and for material over 1 in. in thickness, around a pin the diameter of which is equal to twice the thickness of the specimen.
Halaman 591 - KMnO4 solution, stirring the liquid vigorously and continuously. The permanganate must not be added more rapidly than 10 to 15 cc per minute and the last 0.5 to 1 cc must be added dropwise with particular care to" allow each drop to be fully decolorized before the next is introduced.
Halaman 473 - ... works which concern the manufacture of the material ordered The manufacturer shall afford the inspector, free of cost, all reasonable facilities to satisfy him that the material is being furnished in accordance with these specifications. All tests (except check analyses) and inspection shall be made at the place of manufacture prior to shipment, unless otherwise specified, and shall be so conducted as not to interfere unnecessarily with the operation of the works.
Halaman 628 - This term shall be applied to the finely pulverized product resulting from the calcination of an argillaceous limestone at a temperature only sufficient to drive off the carbonic acid gas.